What do paintball regulators do

It is important to note that low-pressure paintball guns can require you to have paintball regulators. The carbon dioxide can quickly produce a minimum of psi, and the regulator can decrease the gas pressure. Many paintball players choose two different regulators or have a two-regulator system for better performance.

The first pressure regulator might decrease only half the pressure, and the second regulator can lower the pressure again for proper operation of the paintball gun. It will not fire the gun as fast as you would like, so have two regulators be the maximum for your setup. Generally, the regulator you choose and the setup for your equipment comes down to personal preference.

Technically, the only paintball players who need a regulator shoot paintball markers that cannot work under high pressure. Additionally, some markers have a regulator on them already. If you use high-pressure air HPA tanks rather than carbon dioxide, the HPA is stored as a gas, so the pressure remains constant because there is no energy taking place as the liquid converts into usable gas in your tank.

HPA tanks already have regulators in place on tanks, from fixed high pressure, low pressure, and adjustable pressure, which gives you the customization to set the pressure to where you would like.

Decide if you will be running a carbon dioxide or HPA setup as it will determine which paintball regulator will suit your system. Besides the regulator you choose, it is highly recommended to invest in a pressure gauge just if you need to take a quick look to troubleshoot or assess your system. Also, less expensive paintball gun regulators might not be able to shoot fast enough for your preference, so invest wisely. We found it did not leak, was easy to operate, and is highly rebuildable.

Its output pressure can be adjusted to anything between 0 and PSI. It has a maximum input pressure of PSI. Airsoft uses a hard metal alloy that feels solid and sturdy. We did, however, find when used with some tanks, this regulator had slight air leakage. This, of course, is due to the unit leaking with some tanks. But the tanks that it did fit, the pressure was very steady and the gauge worked like it was supposed to.

It has a top input pressure of PSI. It also sports a convenient, built-in gauge. This allows you to readily see your set amount of pressure. The build quality of the Gurlleu regulator is top-notch. It feels solid and sturdy and has a great readout. This will help all of you new folks out there and serve as a refresher course for the veterans.

All paintball guns must have sufficient air pressure in order for them to function properly. This air pressure is what makes the paintball shoot out of your gun.

The more pressure or gas, the farther and harder your shot will travel. Paintball guns that allow you to adjust the velocity with a screw are, in actuality, increasing the power of the striker when it hits the valve.

How long that stays open depends on how hard it is hit. You get more air to pass through the valve the longer it stays open. This is what causes the paintball to expel from your marker. Some models will only work with HPA tanks. If you have one of these guns, a tank regulator is of no use to you. But if the idea of regulating your own pressure is of interest to you, you should look for a good used paintball gun that will allow you to add a regulator.

Many will argue that adding a regulator gives you better airflow. This allows you to have more consistent shots with reliable performance. While this will add extra cost to your paintball gun, you have much more control of your shots, how far they travel, and at what rate of speed.

For the ultimate precision and accuracy, you can set up your paintball gun to run on two separate regulators. This is a costly endeavor, but if you play competitively or professionally, you may want to look into it. Which brings us to…. Some like their tank to be attached under the handle, while others prefer it to be vertical with the receiver.

If you plan on using a bigger tank you may want to run a remote line from your gun. This will allow you to carry your tank on your back. This can greatly impact the pressure your marker gets from the tank. Obviously not all markers are made the same, so you may be forced to mount the regulator in certain areas only. There is an element of risk, however with the right equipment and protective gear, this is reduced by a large amount.

While having fun is important, anything that increases the risk to yourself or others should be kept in mind. Using pressurised air tanks and paintball guns is one of these factors, and pressure build-ups can cause blockages or faults that change how the paintball gun works. If you use something not designed to work together properly, it could cause damage to your equipment. We'll start with what you can't fill it up with. A car compressor isn't going to cut it, you'll need something capable of filling up to bar.

This type of compressor can be found at a local dive shop, or you can pop into our paintball shop. You can also invest in a high-pressure stirrup pump, but be prepared for this to take some time. Another way to fill, and probably the easiest, is to decant from a scuba tank into a smaller paintball or Airsoft high-pressure air tank. Add to Cart. High quality replacement regulator from Ninja Paintball offers a fast refill rate with adjustable output pressure.

They are set at psi from the factory. Standard regs include a steel bonnet and standard size gauge. Regulator replacement should only be First Strike 3K Regs are here! FS Regs are position and output adjustable. They offer superior recharge rates for unparalleled consistency. Out of Stock Compare Quick view. Out of Stock. Standard Output Pressure of psi